Mallory-ignition ACCEL DFI PRO RAM 77141_77142_77143_77144 Bedienungsanleitung PDF herunterladen

ACCEL DFI PRO RAM CHEVY

Installation Instructions.

INSTALLATION EQUIPMENT LIST

The Following is a partial list of the tools you may need for the installation of your

new system.

• Socket set, 3/8” Drive

• Open end wrenches

•Silicone Sealant

• Screw driver set

• Needle nose pliers • Gasket Scraper

• 1- 5/8” Green Lee Punch • hole saw

• Drain bucket

• Timing Light

• Torque Wrench

• Volt/Ohmmeter (example: Snap on MT406, Matco ET 856)

ADDITIONAL PARTS REQUIRED

Intake Manifold Gasket Set

S/B (Mr Gasket # 5820 STK – 5821 Standard Port– 5822 Med/Race Port).

B/B (Mr Gasket # 5827 Oval Port #5828 Rect Port.

Thermostat Housing Gasket # 738

3/8” Stainless Steel Braided Feed Fuel Line & Fittings

160 Degree Fahrenheit Thermostat # 4363 or 180 Deg # 4364

MANIFOLD INSTALLATION INSTRUCTIONS.

Warning: Read and follow instructions before, during and after installation

to preserve warranty. Also disconnect battery leads and drain engine

coolant prior to manifold installation.

In the vast majority of cases, the manifold may be installed without modifications,

if further port matching is required, material removal should be blended up at

least two inches into the runner.

Since the casting lines between the runners and the plenum floor are located

entirely outside of the runner entries, an ideal runner approach radius is insured

as cast.

Note: It may be necessary to purchase some of the parts listed (or the

equivalent) in order to properly complete the manifold installation. Also,

before moving the distributor, set the rotor to the number one cylinder.

Note: To reduce chances of engine contamination by dirt or other foreign

material, it is advisable to clean the engine exterior before starting the

manifolds change.

After removing the distributor and existing intake manifold, clean the gasket

surfaces prior to installing the Small Block Pro Ram system. It is recommended

at this point to use the Green Lee Punches or a hole saw to put a 1 5/8” hole in

the fire wall to accommodate the Main Wire Harness. (Remember to cover

engine completely when drilling through the firewall) Once the gasket surface has

1 2 3 4

Inhaltsverzeichnis

Seite 1 - ACCEL DFI PRO RAM CHEVY

ACCEL DFI PRO RAM CHEVY Installation Instructions. INSTALLATION EQUIPMENT LIST The Following is a partial list of the tools you may need for the inst

Seite 2 - ROUTING AND CONNECTIONS

been cleaned, apply a fine bead of silicone on the bottom sides of the replacement intake gaskets and place on the heads. Next, place a 1/4” bead of s

Seite 3 - MECHANICAL PUMP REMOVAL

Select the ignition type in the Systems screen under IGNITION TYPE SELECTION. FUEL PUMP MOUNTING. The most important component of the high-pressure fu

Seite 4 - MOUNTING THE OXYGEN SENSOR

of the vehicle. ACCEL recommends supporting the fuel line/tubing every three - (3) feet. DUAL FUEL TANKS It is important to note that for vehicles wit

Kommentare zu diesen Handbüchern

Keine Kommentare

Mallory-ignition ACCEL DFI PRO RAM 77141_77142_77143_77144 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für das Auto Mallory-ignition ACCEL DFI PRO RAM 77141_77142_77143_77144 herunter. Mallory Ignition ACCEL DFI PRO RAM 77141_77142_77143_77144 User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für das Auto Mallory-ignition ACCEL DFI PRO RAM 77141_77142_77143_77144