Mallory-ignition Lakewood Safety Bellhousing 15100/15120 Bedienungsanleitung PDF herunterladen

WORK SAFELY!

Installation of this safety bellhousing requires working

underneath vehicle. USE EXTREME C AUTION W H E N

WORKING UNDERNEATH THE VEHICLE. Never get

near or underneath the vehicle until you are confident

that it is safely supported and will not move or fall from

its raised position. DO NOT USE A BUMPER JACK!

PREPARATION FOR INSTALLATION

1. Place the vehicle on a solid, level surface such as a

garage floor to ensure safe installation.

2. Raise the vehicle using appropriate lifting device and

support it using automotive approved support stands

having adequate load capacity.

3. Disconnect the negative (-) cable from the battery.

CAUTION: DO NOT BEGIN THIS INSTALLATION UNTIL

YOU ARE CONFIDENT THAT THE VEHICLE IS SECURE

AND SAFELY SUPPORTED!

Installation Instructions

1. Remove driveshaft, starter motor, transmission and

stock bellhousing.

2. Re m o ve pressure plate and clutch disc from flywheel.

3. At this point, we recommend that you check your

Lakewood Safety Bellhousing for proper alignment with

the crankshaft. This is not a difficult procedure.

Detailed instructions outlining the necessary steps a l o n g

with recommendations for correcting any misalignment are

included in these instructions.

4. After checking and correcting bellhousing alignment,

remove flywheel and install blockplate. Use blockplate

as is (the round hole in the blockplate will correctly

locate the starter nose assuring proper alignment).

Install blockplate over the crankshaft flange and place

over dowel pins in the block.

I M P O RTA N T: In order to comply and meet S.F. I .

bellhousing specification 6.1, it is mandatory that the

safety blockplate be installed with this bellhousing and

all containment fasteners supplied be used in their

correct location (see illustration).

5. Reinstall flywheel and clutch assembly. Be sure to

tighten fasteners using manufacturers recommended

torque specifications.

Note: We recommend the use of Mr. Gasket Ultra-Seal

premium fasteners for clutch and flywheel installation.

Flywheel bolts Mr. Gasket #912

Pressure plate bolts Mr. Gasket #910

I M P O R TA N T: Do not reuse the factory cast iron

flywheel! A high performance quality billet flywheel that

meets S.F.I. specifications is recommended for safety

purposes. Hays off e r s a complete line of high

performance clutches and flywheels to meet safety

requirements.

6. Remove clutch release bearing fork and pivot ball

from stock bellhousing. Reinstall the pivot ball into the

Lakewood bellhousing and attach fork clip onto the

pivot ball. Note: It is recommended to use Lakewood

#15501 Adjustable Pivot Ball in order to obtain the

proper fork geometry. A Heavy-Duty Clutch Fork #15500

is also available to fit most applications.

7. Position your Lakewood Bellhousing over the flywheel/

clutch assembly and slide onto dowel pins in engine

block. Fasten the bellhousing to the engine block using

the 3/8”-16 x 1” (35 ft lbs of torque) and 1/2” bolts (100-

110 ft lbs) grade 8 bolts supplied. Secure the blockplate

to the bellhousing using the supplied grade 8 fasteners

installed in the order shown on the illustration.

IMPORTANT: All fasteners must be used in their proper

location for the bellhousing to meet S.F.I. specification 6.1

8. Replace starter motor, transmission and driveshaft.

Attach clutch linkage and check for proper adjustment.

9. Reconnect battery cable.

INSTALLATION INSTRUCTIONS

Lakewood Safety Bellhousing

Oldsmobile, Buick and Pontiac Applications

#15100 and #15120

NOTICE: This safety bellhousing meets S.F.I. (Safety Foundation Institute) specification 6.1 when used

with the enclosed engine block plate and maximum containment fasteners supplied. It is highly

recommended that an S.F.I. approved flywheel and clutch assembly be used in conjunction

with this bellhousing for additional safety precautions.

1 2 3 4

Inhaltsverzeichnis

Seite 1 - Lakewood Safety Bellhousing

WORK SAFELY!Installation of this safety bellhousing requires workingunderneath vehicle. USE EXTREME C AUTION W H E NWORKING UNDERNEATH THE VEHICLE.

Seite 2

For this product to meet SFI specification 6.1 the fasters listed below must be used.LAKEWOOD 15120 SERIES FASTENER REQUIREMENTBUICK 400-455 V8 AND AL

Seite 3 - Alignment Procedure

INSTRUCTIONS1. Remove clutch assembly from flywheel and installbellhousing on engine block. (It is easier when yo ul e ave the clutch assembly off the

Seite 4

RECOMMENDED OPTIONAL LAKEWOOD & HAYS PRODUCTS• Adjustable Clutch Fork Pivot Ball. This handy item allows adjustment of the clutch fork height when

Kommentare zu diesen Handbüchern

Keine Kommentare

Mallory-ignition Lakewood Safety Bellhousing 15100/15120 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für das Auto Mallory-ignition Lakewood Safety Bellhousing 15100/15120 herunter. Mallory Ignition Lakewood Safety Bellhousing 15100/15120 User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für das Auto Mallory-ignition Lakewood Safety Bellhousing 15100/15120